Check your VIN

Kenworth T440 recalls

28 recall campaigns for the Kenworth T440, newest first.

  1. Kenworth please see the recall report for a complete list of models. 2021–2024 Kenworth C500B, T280, T370 +20 more 24V-915 · December 9, 2024
  2. Kenworth air tanks have an insufficient volume of air for the brake system. 2009–2023 Kenworth C500, T370, T440 +7 more 24V-145 · February 23, 2024
  3. Kenworth engine control module (ECM) may experience an internal electrical short-circuit, causing the engine to stall. 2023 Kenworth K270, K370, T280 +18 more 22V-631 · August 17, 2022
  4. Kenworth steering gears may have been assembled incorrectly, which can cause the gears to fracture. 2022 Kenworth C500, T170, T270 +24 more 22V-547 · July 28, 2022
  5. Kenworth dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail. 2018 Kenworth T270, T370, T440 +16 more 22V-277 · April 25, 2022
  6. Kenworth methane detection system will not function if the system loses power. 2016–2021 Kenworth T270, T280, T440 +5 more 21V-00N · December 29, 2021
  7. Kenworth fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head. 2021 Kenworth T270, T280, T370 +7 more 21V-601 · August 3, 2021
  8. Kenworth sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak. 2018–2021 Kenworth T270, T370, T440 +10 more 21V-391 · May 26, 2021
  9. Kenworth starter interrupt may allow the vehicle to start when the transmission is not in park. 2022 Kenworth T440, T470, T800B +1 more 21V-262 · April 13, 2021
  10. Kenworth osco Tank & Truck Sales, Inc. 2012–2018 Kenworth T440, 348 19V-243 · March 27, 2019
  11. Kenworth internal component in the clutch assembly may fail, possibly resulting in unintended vehicle movement. 2018 Kenworth C500, T270, T370 +14 more 18V-931 · December 21, 2018
  12. Kenworth castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen. 2016 Kenworth K170, T170, T270 +24 more 17V-593 · September 22, 2017
  13. Kenworth affected vehicles are equipped with certain Goodyear LHS Load Range G tires, size 295/75R22.5 G399A, that due to incomplete adhesion, have a tire tread that may partially separate. 2017 Kenworth K370, T270, T370 +10 more 16V-803 · November 4, 2016
  14. Kenworth affected vehicles are equipped with an SR-7 spring brake valve assembly that may have had the primary and secondary service brake applications installed in reverse. 2016 Kenworth T440, T470, T660 +4 more 15V-457 · July 22, 2015
  15. Kenworth DRLs are required to deactivate when the hazard warning lights are activated, however, the DRLs on these vehicles override the hazard flashing functionality after the brake pedal is pushed for more than two seconds. 2011 Kenworth T440, T470, T660 +2 more 15V-458 · July 22, 2015
  16. Kenworth excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces. 2008–2010 Kenworth T440, T800, W900 +6 more 15V-309 · May 26, 2015
  17. Kenworth in the affected trucks, water may leak into the wiper motor. 2011 Kenworth 963, C500, C540 +8 more 15V-271 · May 8, 2015
  18. Kenworth affected vehicles may experience brake drag due to an improperly seated diaphragm in the brake chamber. 2015 Kenworth T270, T370, T440 +11 more 14V-810 · December 29, 2014
  19. Kenworth cummins ISB or ISL engines in these vehicles may have been equipped with Fleetguard UFF-XT fuel filters, part number FF63009, whose filter shell may separate from the fuel filter nut plate causing the engine to stall without warning. 2015 Kenworth K270, K370, T270 +15 more 14V-486 · August 7, 2014
  20. Kenworth condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor. 2014 Kenworth T440, T660, T800 +5 more 14V-086 · February 18, 2014
  21. Kenworth when the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. 2014 Kenworth C500, C550, T170 +23 more 14V-013 · January 24, 2014
  22. Kenworth in the affected vehicles, the engine harness may have been installed incorrectly rendering the neutral start interlock inoperable. 2011 Kenworth T440 14V-008 · January 14, 2014
  23. Kenworth in the affected vehicles, the plastic housing of the Stop/Tail/Turn (STT) lamp can shrink and allow the light bulb to fall out of the mounted retention ring. 2014 Kenworth C500, T170, T270 +9 more 13V-612 · December 5, 2013
  24. Kenworth tread plate is installed on the entry steps such that it does not align with the cab door opening. 2013 Kenworth T440 13V-243 · June 10, 2013
  25. Kenworth in extremely cold conditions, these bendix relay valves may potentially develop internal leakage. 2012 Kenworth T170, T270, T370 +18 more 12V-026 · January 30, 2012
  26. Kenworth 121, "air brake systems." the quick release air valve required in the full truck service brake air line gladhand connection may not have been installed. 2011 Kenworth T440 11V-281 · May 10, 2011
  27. Kenworth certain cast iron slack adjuster housings, which transmit braking force from the brake chamber push rod to the brake cam tube, may include a flow notch in the handle portion of the housing due to an error during the casting process. 2011–2012 Kenworth C500, T170, T270 +6 more 11V-157 · March 7, 2011
  28. Kenworth one of the four harness spade terminal connections to the chassis load center may become completely unseated. 2011 Kenworth C500, T440, T470 +3 more 10V-452 · September 29, 2010