Check your VIN

Peterbilt 384 recalls

19 recall campaigns for the Peterbilt 384, newest first.

  1. Kenworth in the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. 2008–2011 Kenworth T170, T270, T370 +20 more 20V-199 · April 6, 2020
  2. Kenworth castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen. 2016 Kenworth K170, T170, T270 +24 more 17V-593 · September 22, 2017
  3. Kenworth in the affected vehicles, when the transmission shift lever is moved from reverse to neutral, the reverse gear may stay engaged. 2016 Kenworth T680, T800, T880 +4 more 15V-639 · October 9, 2015
  4. Peterbilt affected trucks, equipped with extended-body Leece Neville alternators, have alternator charge cables that may chafe against a formed metal freon discharge line. 2012 Peterbilt 365, 367, 384 +6 more 15V-456 · July 22, 2015
  5. Kenworth excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces. 2008–2010 Kenworth T440, T800, W900 +6 more 15V-309 · May 26, 2015
  6. Kenworth cummins ISB or ISL engines in these vehicles may have been equipped with Fleetguard UFF-XT fuel filters, part number FF63009, whose filter shell may separate from the fuel filter nut plate causing the engine to stall without warning. 2015 Kenworth K270, K370, T270 +15 more 14V-486 · August 7, 2014
  7. Peterbilt in the affected vehicles, if power is interrupted to the seat electronic control unit (ECU), such as when the fuse for that circuit blows, the side air bag would be disabled but there will not be a warning lamp indicator to notify the operator of the malfunction. 2010 Peterbilt 337, 348, 365 +4 more 14V-283 · May 29, 2014
  8. Kenworth condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor. 2014 Kenworth T440, T660, T800 +5 more 14V-086 · February 18, 2014
  9. Kenworth when the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. 2014 Kenworth C500, C550, T170 +23 more 14V-013 · January 24, 2014
  10. Kenworth internal defect in the ignition switch causes the starter to engage when a key is partially inserted, before the key is turned. 2014 Kenworth T170, T270, T370 +20 more 13V-222 · May 28, 2013
  11. Kenworth in extremely cold conditions, these bendix relay valves may potentially develop internal leakage. 2012 Kenworth T170, T270, T370 +18 more 12V-026 · January 30, 2012
  12. Kenworth fast idle control may be activated by the operator while the transmission is in gear. 2008–2011 Kenworth T660, T700, T800 +7 more 11V-380 · July 21, 2011
  13. Kenworth oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components. 2007–2012 Kenworth T2000, T660, T700 +12 more 11V-127 · February 23, 2011
  14. Kenworth manufacturing defect in the seal supplied by a component manufacturer installed on the output shaft of the exhaust gas recirculation (egr) valve actuator may cause eventual delamination of the seal. 2011 Kenworth T660, T700, T800 +7 more 10V-453 · October 1, 2010
  15. Kenworth circumferential weld around the steering shaft tube that welds the splined tube to the NON-SPLINED tube may be mislocated. 2008 Kenworth C500, T2000, T660 +9 more 10V-308 · July 2, 2010
  16. Kenworth mislocation of a circumferential weld may allow the splined tube and NON-SPLINED tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes. 2009 Kenworth T2000, T660, T800 +8 more 09V-258 · August 7, 2009
  17. Kenworth pintle hitch assemblies may have been manufactured in a manner resulting in a reduction of fatigue strength of the pivot pins. 2007–2009 Kenworth T800, W900, 330 +10 more 08V-104 · October 3, 2008
  18. Kenworth certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 2008 Kenworth C500, T2000, T600 +13 more 08V-002 · August 1, 2008
  19. Kenworth certain door latch assemblies on these vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 2008–2009 Kenworth C500, T2000, T660 +10 more 08V-065 · July 2, 2008