Check your VIN

Peterbilt 387 recalls

13 recall campaigns for the Peterbilt 387, newest first.

  1. Kenworth in the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. 2008–2011 Kenworth T170, T270, T370 +20 more 20V-199 · April 6, 2020
  2. Peterbilt affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. 2006 Peterbilt 357, 365, 367 +10 more 15V-132 · March 6, 2015
  3. Kenworth fast idle control may be activated by the operator while the transmission is in gear. 2008–2011 Kenworth T660, T700, T800 +7 more 11V-380 · July 21, 2011
  4. Kenworth degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on C15 engines. 2007–2009 Kenworth C500, T2000, T600 +3 more 11V-203 · March 24, 2011
  5. Kenworth oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components. 2007–2012 Kenworth T2000, T660, T700 +12 more 11V-127 · February 23, 2011
  6. Kenworth bearing surfaces of the extended lube universal joint that attaches the INTER-AXLE driveline to the drive axle may become prematurely worn due to breakdown of lubrication AND/OR excessive heat. 2007 Kenworth T2000, T600, T660 +10 more 10V-634 · December 13, 2010
  7. Kenworth manufacturing defect in the seal supplied by a component manufacturer installed on the output shaft of the exhaust gas recirculation (egr) valve actuator may cause eventual delamination of the seal. 2011 Kenworth T660, T700, T800 +7 more 10V-453 · October 1, 2010
  8. Kenworth circumferential weld around the steering shaft tube that welds the splined tube to the NON-SPLINED tube may be mislocated. 2008 Kenworth C500, T2000, T660 +9 more 10V-308 · July 2, 2010
  9. Kenworth mislocation of a circumferential weld may allow the splined tube and NON-SPLINED tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes. 2009 Kenworth T2000, T660, T800 +8 more 09V-258 · August 7, 2009
  10. Kenworth certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 2008 Kenworth C500, T2000, T600 +13 more 08V-002 · August 1, 2008
  11. Kenworth certain door latch assemblies on these vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 2008–2009 Kenworth C500, T2000, T660 +10 more 08V-065 · July 2, 2008
  12. Peterbilt on certain peterbilt trucks, the longitudinal seams on the fuel tanks were fabricated using an incorrect weld speed for the given material thickness. 2008 Peterbilt 367, 386, 387 +1 more 07V-409 · October 9, 2007
  13. Peterbilt on certain trucks, the fifth wheel king pin release air valve internal spool was installed backwards. 2006 Peterbilt 379, 387 07V-033 · June 2, 2007